Free Refresh Rate Test

A refresh rate test shows how many times per second the display redraws. This free refresh rate test reads it in the browser: the Hz the display is actually running, a moving bar for motion clarity, and why a 144Hz panel can still report 60. The number comes from the browser's frame clock, so it confirms the active display mode — it is not a laboratory measurement of the panel.

No signup · Runs in your browser · Desktop and mobile

← → change speed · Esc exit

Live refresh rate test

Live readouts from this browser. Start test opens the moving bars fullscreen.

—Hz

—

Frame time
Current FPS
—
Average FPS
—
1% low
—
Frame interval
—
Dropped frames
—
Stability
—
Resolution
—
Pixel ratio
—
Motion comparison
960 px/s

Read the figure at the top first. Then start the test and follow the bar at each speed: smearing, a soft trail or a doubled edge means the panel is not keeping up with the motion, not that the test broke. If the number is lower than the panel's rating, the table and the checklist below show where the limit usually is. Run the refresh rate test again after each change.

Which port and cable each mode needs

The minimum link for common modes at 8-bit colour without compression. Both ends and the cable must support it; the lowest one sets the limit.

ModeHDMIDisplayPort
1080p at 60Hz1.41.2
1080p at 144Hz2.0 (many 1.4 ports stop at 120Hz)1.2
1080p at 240Hz2.01.2
1440p at 60Hz1.41.2
1440p at 144Hz or 165Hz2.01.2
1440p at 240Hz2.11.4
4K at 60Hz2.01.2
4K at 120Hz2.11.4
4K at 144Hz and above2.11.4 with DSC, or 2.1

Cables are rated separately: HDMI 2.0 modes need a cable sold as Premium High Speed, HDMI 2.1 modes need Ultra High Speed. A USB-C port carries video only if it supports DisplayPort Alt Mode, and then behaves like the DisplayPort version it implements. 10-bit colour and HDR need more bandwidth than the table shows; Display Stream Compression (DSC) lets a slower link carry a faster mode when both ends support it.

Still reading 60 Hz? Check these in order

  1. Is the higher rate selected? Windows: Settings › System › Display › Advanced display. macOS: System Settings › Displays › Refresh Rate. Many monitors ship at 60Hz and the OS rarely raises it. If the option is missing, go on.
  2. What does the monitor's menu say about the input? If it also reads 60Hz, the signal is capped before it reaches the panel: compare your port and cable with the table above. Laptop HDMI ports are often 1.4, and on a desktop a port on the motherboard runs from the integrated GPU instead of the graphics card.
  3. Is a dock, dongle or adapter in the chain? Plug the monitor in directly. Many USB-C hubs and HDMI adapters top out at 4K 30Hz or 60Hz whatever the cable.
  4. Is the laptop on battery? Plug in and switch to a balanced or performance profile before reading again.
  5. Everything above checks out? Then the browser is the cap. Safari on iPhone runs pages at 60 frames per second, power-saving modes can throttle animation, and with two monitors the reading follows the one the browser window is on.

What a refresh rate test can and cannot measure

What the number on this page is

Browsers do not expose the refresh rate directly, so this refresh rate checker times the frames the browser draws. Those frames follow the mode your operating system has set, which is why the result matches your display settings. If the browser gives no usable timing, the page says so instead of guessing.

What this page cannot do

The number is the mode the compositor is driving right now, not a specification of the panel. A 240Hz monitor left at 60Hz reads 60, and the page has no way to ask the monitor what it supports. Because it times frames rather than light, it says nothing about response time or input lag either. For dead pixels, bleed and uniformity, run the full monitor test; for a ghost of a fixed element, run the burn in test.

This page versus the monitor's own menu

The monitor's on-screen menu reports the signal it receives, so reading both side by side shows whether the limit is the link, the browser or the panel.

60Hz144Hz
One speed, two refresh rates: the 60Hz trail (top) is more than twice as long. Diagram.

1440p 144Hz monitor on a laptop HDMI port

This page reads

60Hz, and the moving bar looks clearly more smeared than it should.

Monitor menu says

Input signal 60Hz.

The two agree, so the panel is fine and the link is the limit: an HDMI 1.4 port lacks the bandwidth for 1440p at 144Hz. Use DisplayPort, or an HDMI 2.0 port and cable, then choose 144Hz in your display settings and check the reading again.

60HzSafari120HzNative app
Sketch: what Safari reports, next to what the same phone does in its own apps.

iPhone with a 120Hz ProMotion display

This page reads

60Hz in Safari, although the phone is sold as 120Hz.

iOS shows

Low Power Mode on, which caps the display at 60Hz.

Turn Low Power Mode off and reload. If Safari still reports 60, the cap is the browser: Safari on iPhone runs page animation at 60 frames per second by default. Nothing is wrong with the display; judge 120Hz by scrolling in native apps instead.

Drawing of dark smear behind a moving block (top) and the bright edge of too much overdrive (bottom).

VA gaming monitor at 144Hz or 165Hz

This page reads

The rated Hz, correct, but dark objects moving over dark grey leave a dark smear.

Monitor menu says

The same refresh rate, and an overdrive setting (often called Response Time).

A matching reading means the cable and settings are fine. The smear is slow pixel response on dark transitions, typical of VA panels, so it looks the same on any cable and any device. Set overdrive to its middle setting; the highest usually adds bright halos behind moving edges. Some dark smear is normal for VA.

When a refresh rate test is worth two minutes

New high-refresh monitor

Many monitors ship set to 60Hz, and operating systems rarely raise the rate on their own. Run the refresh rate test as soon as it is connected, then set the highest mode in display settings and run it again. Run a dead pixel test on day one as well, while the return window is open.

Laptop on battery

Battery saver modes often drop a 120Hz or 144Hz panel to 60Hz, and some browsers throttle animation as well. Plug in, switch to a balanced or performance profile, and compare the reading against the one on battery.

After a cable or dock change

A new dock, adapter or cable can quietly cap the signal at 60Hz even when the picture looks fine. Run a quick refresh rate test after any swap, and check that the dock supports the resolution and rate you need.

Frequently asked questions

Why does my 144Hz monitor show 60Hz?

Usually the display mode is still set to 60Hz, or the connection cannot carry 144Hz. Raise the refresh rate in display settings, then check the cable, the port and any dock or adapter in between.

Can a browser measure real refresh rate?

Not directly. A browser times its own frames, which follow the refresh rate the OS has set, so it confirms the active mode. It cannot measure the panel itself, and Safari limits pages to 60Hz by default.

Is refresh rate the same as frame rate?

No. Refresh rate is how often the display redraws, set by the panel and the OS. Frame rate is how many new images software produces. A frame rate test in a game measures the second, not the first.

What cable do I need for 144Hz or 240Hz?

For 1080p at 240Hz or 1440p at 144Hz, DisplayPort 1.2 or HDMI 2.0 is enough. For 1440p at 240Hz or 4K at 144Hz, use DisplayPort 1.4 or HDMI 2.1, with a cable certified for that speed.